Calculate your savings with SpillFix Spill Absorbent

The extraordinary absorbency and lightweight nature of SpillFix spill absorbent translates to significant cost savings associated with spills and leaks.

  • Save by using less product to clean a spill
  • Save time to clean up a spill
  • Save in the cost of waste disposal

Use the calculator below to estimate your annual savings by switching to SpillFix from traditional clay-based absorbent you are using now.

SPILLFIX SAVINGS CALCULATOR

close

My current annual use is

Weight of Oil-Dri* clay absorbent bags

Current bag price:

You're saving when switching to SpillFix

More settings can be adjusted by clicking the preferences a black cog icon.

* Oil-Dri is shown as an example of a commonly used traditional clay-based industrial absorbent.

By switching to SpillFix my total annual savings will be*

$

Savings on product cost

$

Product savings are calculated on the basis that a 1 gallon spill needs 25lbs of Oil-Dri to clean up, while the equivalent amount of SpillFix needed is only 2.86lbs. Further saving area achieved through the re-usability of SpillFix.

When no savings are shown it is because SpillFix is costing slightly more than the low price you have entered for Oil-Dri. So the addition of the saving amounts below will then exceed the total savings shown.

Savings on deliveries

$

Delivery costs are reduced as 75% less product is required with SpillFix. The savings are calculated on an estimated 20¢ delivery cost per bag.

The delivery cost per bag can be adjusted by clicking the preferences a black cog icon.

Savings on disposal

$

Disposal waste is reduced 66% by weight and 75% by volume". The savings are determined by product weight, absorption capacity and absorbed oil weight. Disposal cost is then calculated at a rate of $50 per ton.

The disposal cost per ton can be adjusted by clicking the preferences a black cog icon.

Savings on haulage

$

The savings are determined by product weight, absorption capacity and absorbed oil weight. Haulage cost is then calculated at a rate of $150 per 7 ton load.

The disposal cost per ton can be adjusted by clicking the preferences a black cog icon.

In addition to the savings shown further cost reduction can be made by reusing SpillFix until saturated. Switching to SpillFix will also:


no residue slick

no heavy lifting

75% less warehouse

reduce waste by 66%

no ruptured bags

Reduce clean up time by 80%

Eliminate all health risks

Reduce warehousing by 75%

Create 66% less waste for disposal

Eliminate spoilage from ruptured bags

Remove any threat of OSHA fines

* The savings shown are calculated from actual case studies of industrial absorbent users that have switched to SpillFix. These saving represent a conservative estimate on what you are likely to save, but in no way constitute any guarantee for which SpillFix is liable.

Preferences

close

SpillFix default cost per bag

$

Delivery cost per bag

$

Disposal cost per ton

$

Waste haulage tonage

Waste haulage cost per ton load

$

Are you worried about a liability claim or OSHA fines?

YOU SHOULD BE IF

  • Your workers are carrying heavy clay absorbent bags
  • Your workers are breathing in carcinogenic Silica dust
  • Your workers can’t clean up a spill immediately and effectively

CHOOSE SPILLFIX AND STOP PUTTING YOUR WORKERS IN HARM’S WAY

  • Instant slick-free spill cleanup prevents Slip and Fall injuries.
  • Lightweight spill absorbent prevents back injuries.
  • Silica dust free spill absorbent prevents lung disease.

  • “Bar-B-Que sauce is easy enough to clean up when it’s on your fingers and lips, but it’s an entirely different story when a five-gallon jug of it ruptures and flows onto a warehouse floor. SpillFix was applied to the entire disaster area – from the pallet to the cardboard, the shrink wrap and the growing puddle on the floor. In three and a half minutes, the entire mess was cleaned, and the warehouse was restored to a safe workplace again — using just one product.”

    Warehouse Supervisor, Food Manufacturing

  • "I have yet to encounter a spill or leak this product can’t handle. Without SpillFix, my job would be much more difficult to achieve. I fully give this product a 100% success. I’ve been working here for almost 8 years. Best thing I’ve ever used in my job to date." Read case study.

    Ground Operations Administrator, FedEX

  • "Our company mission is all about sustainability so SpillFix is a great fit for us."

    John C., Oil & Steel Industry

  • "I’ve been in this business for a long time, and I’ve never seen anything like it." Read case study.

    Scott B, Maintenance Manager

  • "SpillFix left no residue removing any slip and fall threat to our workers."

    Chris B., Heavy Manufacturing Industry

  • "The most important thing for us is that the product works, and it does." Read case study.

    Travis B., Operations Manager

  • "SpillFix played an essential role to get us LEAN Certified."

    Anonymous

  • "SpillFix is the fastest, easiest and the most effective absorbent we have ever used. Hands down."

    Tim O., Manufacturing Industry

  • "SpillFix helps us keep spills under control in dorms, cafeterias and other common areas. Huge savings in disposal costs and maintenance and repairs deferred."

    Joe K., Higher Education Sector

  • "SpillFix cleans the spills up on our floors better than the previous current products. However, the cleaning has to be done correctly, this is a watch-out-change for our team. In the past, we put down our current product and walked away for a few hours or a day. SpillFix should be cleaned up right away." Read case study.

    Fleet Manager, Beverage Manufacturer
0